DANAK

Reg. No. 200 Accreditation for testing and calibration

Page: 1 2 3 4 5 6 7 all
EA Scope Equipment Quantity Range
Low
Limit		 Range
High
Limit		 U(CMC)
Low
Limit		 U(CMC)
High
Limit		 Working
Standard		 Method Remark In Situ Location
Chemical Gas concentrations Volume %
(CO2 ) 		42   ppm 48   vol.% 2  % 2,8  % Reference gas and flow meter Internal Procedure D1-12 FUGT-Aarhus
Temperature Temperature Gauges Temperature -45   °C 155   °C 0,14  °C 0,14  °C Dry block calibrator Internal Procedure Auto D1-2.1 Digitaltermometer, opløsning 0,01°C X AUTO-On site
Pressure and vacuum Manometers Pressure -100   kPa 0   kPa 1,5  kPa 1,5  kPa Pressure Calibrator Internal procedure Auto D1-3.1, DS/EN 837 Vakuum. Opløsning 1 kPa X AUTO-On site
Pressure and vacuum Manometers Pressure 0   MPa 2   MPa 1,7  kPa 1,7  kPa Pressure Calibrator Internal procedure Auto D1-3.1 Overtryk. Opløsning 1 kPa X AUTO-On site
Pressure and vacuum Manometers Pressure 0   Pa 7   MPa 2  kPa 9  kPa Pressure Calibrator Internal procedure Auto D1-3.1 Overtryk. Opløsning 1 kPa X AUTO-On site
Pressure and vacuum Manometers Pressure 0   Pa 30   MPa 13  kPa 40  kPa Pressure Calibrator Internal procedure Auto D1-3.1, DS/EN 837 Resolution 10 kPa X AUTO-On site
Pressure and vacuum Manometers Pressure 0   Pa 70   MPa 48  kPa 48  kPa Pressure Calibrator Internal procedure Auto D1-3.1 Overtryk. Opløsning 10 kPa X AUTO-On site
Force and torque Torque measuring devices Torque 1   Nm 1100   Nm 1,8  % 0,62  % Torque Wrench Analyzer Internal procedure Auto D1-6.1, DS/EN ISO 6789-2:2017 X AUTO-On site
Dimensional Caliper Length 0   mm 500   mm 20  μm 48  μm Gauge blocks Internal procedure Auto D1-8.1 Opløsning 0,01 mm X AUTO-On site
Dimensional Micrometer (all types) Length 0   mm 25   mm 3,1  μm 14,2  μm Gauge blocks Internal procedure Auto D1-8.1 Opløsning 0,01 mm X AUTO-On site
Dimensional Dial gauges/centrumindicators Length 0   mm 25   mm 2,8  μm 3,3  μm Dial Gage Tester Internal procedure Auto D1-8.1 Opløsning: 0,001 mm X AUTO-On site
Dimensional Dial gauges/centrumindicators Length 0   mm 300   mm 3,1  μm 9,5  μm Lenght Transducer (Digital Dial Gauge) and Gauge Blocks Intern procedure Auto D1-8.1 Including Build-In Lenght Tranducers. Resolution 0,001 mm. X AUTO-On site
Electricity DC and LF Electrical equipment (DC) Voltage (DC) 0   V 1100   V 5,7  μV 154  mV Multifunctioncalibrator Internal procedure Auto D1.5.1 Opløsning: 0,001mV - 0,01V X AUTO-On site
Electricity DC and LF Electrical equipment (DC) Current (DC) 0   A 20   A 0,02  nA 10  mA Multifunctioncalibrator Internal procedure Auto D1.5.2 Opløsning: 0,01µA - 1mA X AUTO-On site
Electricity DC and LF Electrical equipment (DC) Current (DC) 20   A 1000   A 0,05  A 2,5  A Multifunctioncalibrator Internal procedure Auto D1.5.2 X AUTO-On site
Electricity DC and LF Electrical equipment (DC) Resistance 0   Ω 400   MΩ 23  mΩ 0,34  MΩ Multifunctioncalibrator Internal procedure Auto D1.5.3 Opløsning: 0,001 ohm - 0,01Mohm X AUTO-On site
Electricity DC and LF Electrical equipment (AC) Voltage (AC) 0   V 800   V 0,45  mV 742  mV Multifunctioncalibrator Internal procedure Auto D1.5.4 Opløsning: 0,001mV - 0,01V X AUTO-On site
Electricity DC and LF Tachometers RPM 600   rpm 6000   rpm 2,3  rpm 2,9  rpm Enginesimulator Internal procedure Auto D1.5.5 Generering. Opløsning: 1 rpm X AUTO-On site
Electricity DC and LF Tachometers RPM 0   rpm 90000   rpm 2,1  rpm 56,1  rpm Tachometer Internal procedure Auto D1.5.5 Måling, opløsning: 1rpm X AUTO-On site
Electricity DC and LF Motor testers Cam angle 0   ° 100   ° 0,12  ° 0,12  ° Enginesimulator Internal procedure Auto D1.5.6 Opløsning: 0,1% X AUTO-On site
Electricity DC and LF Motor testers 0   ° 50   ° 0,29  ° 0,29  ° Enginesimulator Intern procedure Auto D1.5.6 opløsning: 0,1° X AUTO-On site
Electricity DC and LF Electrical equipment (AC) Current (AC) 0   A 20   A 0,44  μA 51  mA Multifunctioncalibrator Internal procedure Auto D1.5.7 X AUTO-On site
Electricity DC and LF Electrical equipment (AC) Current (AC) 20   A 200   A 125  mA 700  mA Multifunctioncalibrator Internal procedure Auto D1.5.7 X AUTO-On site
Force and torque Brake testers Force 1   kN 31   kN 32,1  N 302  N weigths and weigtharm Internal procedure Auto D1.7.1 Opløsning: 2daN X AUTO-On site
Electricity DC and LF Electrical equipment (AC) Current (AC) 200   A 1000   A 1  A 3,5  A Multifunctioncalibrator Internal procedure Auto D1.5.7 X AUTO-On site
Force and torque Torque wrenches Torque 1   Nm 1100   Nm 1,8  % 0,62  % Torque Wrench Analyzer Internal procedure Auto D1-6.1, DS/EN ISO 6789:2003 X AUTO-On site
Force and torque Torque transducers Torque 0,2   Nm 10   Nm 1  % 0,5  % Transfer Torque Wrench Internal Procedure Auto D1.9.1 Level 1 AUTO-Aarhus
Force and torque Torque transducers Torque 10   Nm 100   Nm 0,5  % 0,4  % Transfer torque wrench - TTS 100 Nm Internal procedure Auto D1.9.1 Level 1 AUTO-Aarhus
Force and torque Torque transducers Torque 100   Nm 1100   Nm 0,4  % 0,4  % Transfer torque wrench - TTS 1000 Nm Internal procedure Auto D1.9.1 Level 1 AUTO-Aarhus
Force and torque Torque transducers Torque 10   Nm 100   Nm 0,8  % 0,8  % Torque Transducer Internal procedure Auto D1.9.1 Level 2 X AUTO-Århus
Force and torque Torque transducers Torque 1   Nm 10   Nm 0,9  % 0,8  % Torque Transducer Internal procedure Auto D1.9.1 - Level 2 X AUTO-Aarhus
Force and torque Torque transducers Torque 100   Nm 1100   Nm 0,8  % 0,7  % Torque Transducer Internal procedure Auto D1.9.1 Level 2 X AUTO-Århus
Time and frequency Time and frequence meas. eq. Frequency 0   Hz 10   MHz 0,0006  Hz 300  Hz Multifunctioncalibrator Internal procedure Auto D1.5.5 X AUTO-On site
Time and frequency Time and frequence meas. eq. Frequency 40   Hz 400   Hz 0,058  Hz 0,58  Hz Installation testers and Insulation testers calibrator. Intern procedure D1-11.1 Resolution: : 0,1 Hz- 1Hz X AUTO-On site
Force and torque Force transducers Force
(0,001 - 1,3 kN ) 		1   N 1300   N 0,05  % 0,05  % Deadweight DS/EN ISO 376:2011 Calibration of Force Transducer Tension. Internal method K03. KRAFT-Aarhus
Force and torque Force transducers Force 0,1   kN 1   kN 0,09  % 0,05  % Force Transducer DS/EN ISO 376:2011 Calibration of Force Transducer Tension. Internal method K03. KRAFT-Aarhus
Force and torque Force transducers Force 1   kN 600   kN 0,05  % 0,05  % Force Transducer DS/EN ISO 376:2011 Calibration of Force Transducer Tension. Internal method K03. KRAFT-Aarhus
Force and torque Force transducers Force
(0,001 - 1,3 kN ) 		1   N 1300   N 0,05  % 0,05  % Deadweight DS/EN ISO 376:2011 Calibration of Force Transducers Compression. Internal method K03. KRAFT-Aarhus
Force and torque Force transducers Force 0,1   kN 100   kN 0,09  % 0,05  % Force Transducers DS/EN ISO 376:2011 Calibration of Force Transducer Compression. Internal method K03. KRAFT-Aarhus
Force and torque Force transducers Force 100   kN 1000   kN 0,05  % 0,08  % Force Transducers DS/EN ISO 376:2011 Calibration of Force Transducer Compression. Internal method K03. KRAFT-Aarhus
Force and torque Force transducers Force 1000   kN 2000   kN 0,08  % 0,17  % Force Transducers DS/EN ISO 376:2011 Calibration of Force Transducer Compression. Internal method K03. KRAFT-Aarhus
Force and torque Force transducers Force 2000   kN 3000   kN 0,17  % 0,18  % Force Transducers DS/EN ISO 376:2011 Calibration of Force Transducer Compression. Internal method K03. KRAFT-Aarhus
Force and torque Force transducers Force 3000   kN 5000   kN 0,18  % 0,18  % Force Transducers DS/EN ISO 376:2011 Calibration of Force Transducer Compression. Internal method K03. KRAFT-Aarhus
Force and torque Material testing machines Force 1   N 600   kN 0,4  % 0,3  % Deadweights and Force Transducers EN ISO 7500-1:2018 Calibration of Force Equipment Tension based, including Hydraulic Jack's, Dynamometers ect. Internal method K04. X KRAFT-Aarhus
Force and torque Material testing machines Force 1   N 25   N 0,4  % 0,4  % Deadweights and Force Transducers EN ISO 7500-1:2018; EN 12390-4:2019 Calibration of compression testing machines, including hydraulic jack's, dynamometers ect. Internal method K01 & K04. X KRAFT-Aarhus
Force and torque Material testing machines Force 25   N 1   kN 0,4  % 0,3  % Deadweights and Force Transducers EN ISO 7500-1:2018; EN 12390-4:2019 Calibration of compression testing machines, including hydraulic jack's, dynamometers ect. Internal method K01 & K04. X KRAFT-Aarhus
Force and torque Material testing machines Force 1   kN 5000   kN 0,3  % 0,3  % Deadweights and Force Transducers EN ISO 7500-1:2018; EN 12390-4:2019 Calibration of compression testing machines, including hydraulic jack's, dynamometers ect. Internal method K01 & K04. X KRAFT-Aarhus
Force and torque Material testing machines Force 1   N 1300   N 0,25  % 0,25  % Force Transducers EN ISO 7500-1:2018 Calibration of Force Equipment Tension & Compression, including Dynamometers ect. Internal metod K04. X KRAFT-Aarhus
Hardness Hardness testers Hardness (Brinell) 20   HB 5000   HB 11  % 1  % Force Transducers, Geometrical Scale, Stop Watch. DS/EN ISO 6506-2:2018 Calibration of Hardness Testers, Direct Method. Except calibration of the endenter. For endentions > 0,2 mm. Internal method K05.1. X KRAFT-Aarhus
Hardness Hardness testers Hardness (Vickers) 50   HV 900   HV 2,5  % 2,5  % Force Transducers, Geometrical Scale, Stop Watch. DS/EN ISO 6507-2:2018 Calibration of Hardness Testers. Direct Method. Except calibration of the endenter. For endentions > 0,2 mm. Internal method K05.2. X KRAFT-Aarhus